Showing all 13 resultsSorted by popularity
-
$5.19
Features
- The LRU26Z features an open design and ability to field-adjust the slope, ideal for both retrofit or new applications.
- May be sloped down from 0° (0:12 pitch) to 49° (14:12). For slopes greater than 45°, allowable downloads are 0.85 of table loads.
- May be sloped up from 0° to 45°.
- Can be installed using nails or Strong-Drive SD Connector screws.
-
$1.13
Features:
- MAB15Z anchors mudsill to concrete block, poured walls or slab foundations
- Nominal sill size: 2×4, 2×6, 2×8, 2×10, 2×12
- Made from 18-gauge steel
- ZMAX galvanization offers extra corrosion resistance for exterior and treated-wood applications
-
$0.52
Features:
- Embossments in bend line strengthen connection
- The top flange features an arrow line indicator to aid correct installation
- Made from 18-gauge steel
- Galvanized (G90) for extra corrosion resistance
-
$4.07
Features:
- An indented embedment line ensures accurate embedment depth
- The HETA24 is compatible with the Simpson Strong-Tie preassembled TSS snap-in seat
- Load rated for wind and seismic forces
- 20-in. exposed length
- Embed 4 in. into a poured concrete bond beam or grouted block wall
-
$6.91
Features:
- THA418 offers extra-long straps for height adjustability and top-flange installation
- Zinc Galvanized, G90 Finish
- Top-flange or face-mount installation
Wood Construction Connectors Resources
-
$0.87
Features:
- Great for connecting 2x deck joists on top of a perpendicular beam
- Install in pairs on either side of the rafter/truss/joist to provide resistance to uplift and lateral forces
- Use also for a variety of connections where one member crosses another
- Made from 18-gauge steel
- Galvanized (G90) for extra corrosion resistance
-
$46.31
Features:
- CB66 features increased uplift resistance for wind or seismic loading
- Bolt hole locations meet code-required spacing for optimal capacity
- Nominal column size: 6×6
- Made from 7-gauge steel
- Galvanized (G90) for extra corrosion resistance
-
$1.08
Features
- LUS24Z cannot be modified
- Works for a wide range of applications
- Features speed prongs used to temporarily position and secure the connector for easier and faster installation
- LUS-series hangers are tested, load rated and code compliant
-
$46.29
Features
- APVB66R is designed to meet stringent building codes for seismic or high-wind events
- Slotted for adjustability
- Features 1″ standoff to help prevent rot at post end
- Outdoor Accents side plates available (see APVBDSP)
- Fastener holes are slightly offset to help prevent fastener interference
-
$155.89
Features
- APVB1010R has an adjustable design for fine-tuning of post placement
- Corrosion-resistant
- 1″ standoff
- Strong connection
- Building code compliant
-
$2.29
Features:
- An indented embedment line ensures accurate embedment depth
- HETA16 is compatible with the Simpson Strong-Tie preassembled TSS snap-in seat
- Load rated for wind and seismic forces
- 12-in. exposed length
- Embed 4 in. into a poured concrete bond beam or grouted block wall
-
$3.00
Features:
- Replaces additional framing and toe-nailing
- Suitable for most installations on nominal 2×10 or 2×12 header/rim board
- May be installed flush with the top of the carrying member or lower on the face
- Interchangeable for left or right applications
- Made from 18-gauge steel
-
$13.49
Features:
- LGT2 is suitable for retrofit applications
- The embossments add stiffness in crucial areas for improved performance
- Simple to install and can be installed on the inside or outside of the wall
- Load rated to resist high-wind forces
- 2-ply
