Showing all 39 results

  • DIAB50 Simpson drop-in anchor

    Simpson Strong-Tie DIAB50 DIAB Drop-In Internally Threaded Anchor for 1/2-in. Rod

    Standard Shipping

    $0.43

    Features:

    • Faster installation than previous drop-in anchor design sets with 40% fewer hammer hits
    • Positive-set marking system indicates when anchor is properly set
    • Zinc-plated carbon steel
    • Length: 2 in.
    • Drill bit diameter: 5/8 in.
    Simpson Strong-tie DIAB50 Product Page
    Minimum order quantity: 50
    Order in multiples of: 50
    Add To CartLoading Done
  • Max TW898 21 gauge rebar tie wireMax tw898 tie wire

    [50 Rolls] MAX TW898 21 Gauge Rebar Tie Wire for RB397 RB398 RB517 and RB518 rebar tiers only – 50 Roll Case

    Free Shipping

    $279.64

    Features

    • 21 Gauge Steel Tie Wire
    • Bare steel with no coating
    • For use with MAX RB397, RB398, RB517 and RB518
    Add To CartLoading Done
  • [50 Pack] Simpson Strong-Tie THD37400CS Titen HD 3/8 in. x 4 in. Zinc-Plated Countersunk Head Heavy-Duty Screw Anchor

    Standard Shipping

    $61.84

    Features

    • Tested in accordance with ACI 355.2, AC193 and AC106
    • Qualified for static, wind and seismic loading conditions
    • Standard fractional sizes, hole size same as anchor size
    • No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
    • Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
    • 6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
    • Countersunk head allows screw anchor applications incompatible with a hex head
    • Available in 1/4″ and 3/8″ diameters
    Add To CartLoading Done
  • THD37500H

    [50 Pack] Simpson Strong-Tie THD37500H Titen HD 3/8 in. x 5 in. Heavy-Duty Screw Anchor

    Standard Shipping

    $95.38

    Features

    • Tested in accordance with ACI 355.2, AC193 and AC106
    • Qualified for static, wind and seismic loading conditions
    • Thread design undercuts to efficiently transfer the load to the base material
    • Standard fractional sizes
    • Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
    • No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
    • Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
    • Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
    • Reuse of the anchor will not achieve listed loads and is not recommended
    Add To CartLoading Done
  • Max TW898-PC poly coated tie wire

    [50 Rolls] MAX TW898-PC Poly Coated 21 Gauge Rebar Tie Wire

    Free Shipping

    $629.50

    Features

    • 21 Gauge Steel Tie Wire
    • Bare steel with no coating
    • For use with MAX RB397, RB398, RB517 and RB518
    Add To CartLoading Done
  • 3PB

    Simpson Strong-Tie 3PB Quick-Lock Pier Boot

    Standard Shipping

    $235.69

    Features

    • Quick and easy installation
    • Made of durable noncorrosive plastic
    • No tools required
    • Made in the USA with global materials
    Add To CartLoading Done
  • 3BB

    Simpson Strong-Tie 3BB Quick-Zip Bar Booster

    Standard Shipping

    $249.89

    Features

    • Quick and easy installation
    • Made of durable noncorrosive plastic
    • No tools required
    • Made in the USA with global materials
    Add To CartLoading Done
  • 6-2IN-UBC

    Simpson Strong-Tie 4-2IN-UBC Quick-Lock Unibar Centralizer

    Standard Shipping

    $242.39

    Features

    • Quick and easy installation
    • Made of durable noncorrosive plastic
    • Snaps over the rebar
    • Made in the USA with global materials
    Add To CartLoading Done
  • 7422SD1-PWR7422SD1-PWR

    [Pack of 50] DeWalt 7422SD1-PWR 1/2 in. X 3-3/4 in. Power-Stud Carbon Steel Wedge Expansion Anchor

    Standard Shipping

    $45.58

    Features

    • Consistent performance in high and low strength concrete
    • Nominal drill bit size is the same as the anchor diameter
    • Anchor can be installed through standard fixture holes
    • Length ID code and identifying marking stamped on head of each anchor
    • Anchor design allows for follow-up expansion after setting under tensile loading
    Add To CartLoading Done
  • 7413SD1-PWR7413SD1-PWR

    [Pack of 50] DeWalt 7413SD1-PWR 3/8 In. x 3 In. Power Stud Carbon Steel Wedge Expansion Anchor

    Standard Shipping

    $17.29

    Features

    • Consistent performance in high and low strength concrete
    • Nominal drill bit size is the same as the anchor diameter
    • Anchor can be installed through standard fixture holes
    • Length ID code and identifying marking stamped on head of each anchor
    • Anchor design allows for follow-up expansion after setting under tensile loading
    Add To CartLoading Done
  • [50 Pack] Simpson Strong-Tie THD37600H Titen HD 3/8 in. x 6 in. Heavy-Duty Screw Anchor

    Standard Shipping

    $106.92

    Features

    • Tested in accordance with ACI 355.2, AC193 and AC106
    • Qualified for static, wind and seismic loading conditions
    • Thread design undercuts to efficiently transfer the load to the base material
    • Standard fractional sizes
    • Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
    • No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
    • Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
    • Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
    • Reuse of the anchor will not achieve listed loads and is not recommended
    Add To CartLoading Done
  • [50 Pack] Simpson Strong-Tie THDB25412CS Titen HD 1/4 in. x 4-1/2 in. Zinc-Plated Countersunk Head Heavy-Duty Screw Anchor

    Standard Shipping

    $56.28

    Features

    • Tested in accordance with ACI 355.2, AC193 and AC106
    • Qualified for static, wind and seismic loading conditions
    • Standard fractional sizes, hole size same as anchor size
    • No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
    • Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
    • 6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
    • Countersunk head allows screw anchor applications incompatible with a hex head
    • Available in 1/4″ and 3/8″ diameters
    Add To CartLoading Done
  • THD37300CS6SS

    [50 Pack] Simpson Strong-Tie THDC25200H6SS Titen HD 1/4 in. x 2 in. Type 316 Stainless-Steel Heavy-Duty Screw Anchor

    Standard Shipping

    $179.09

    Features

    • THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
    • Ideal for exterior or corrosive environments
    • Less carbon steel, less expansion
    • Installs with an impact wrench or by hand tool
    • Tested in accordance with ACI355.2, AC193 and AC106
    Add To CartLoading Done
  • [50 Pack] Simpson Strong-Tie THD37212CS Titen HD 3/8 in. x 2-1/2 in. Zinc-Plated Countersunk Head Heavy-Duty Screw Anchor

    Standard Shipping

    $62.17

    Features

    • Tested in accordance with ACI 355.2, AC193 and AC106
    • Qualified for static, wind and seismic loading conditions
    • Standard fractional sizes, hole size same as anchor size
    • No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
    • Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
    • 6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
    • Countersunk head allows screw anchor applications incompatible with a hex head
    • Available in 1/4″ and 3/8″ diameters
    Add To CartLoading Done
  • THD37300CS6SS

    [50 Pack] Simpson Strong-Tie THD37600H6SS Titen HD 3/8 in. x 6 in. Type 316 Stainless Steel Heavy-Duty Screw Anchor

    Free Shipping

    $374.62

    Features

    • THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
    • Ideal for exterior or corrosive environments
    • Less carbon steel, less expansion
    • Installs with an impact wrench or by hand tool
    • Tested in accordance with ACI355.2, AC193 and AC106
    Add To CartLoading Done
  • [50 Pack] Simpson Strong-Tie THD37134H Titen HD 3/8 in. x 1-3/4 in. Heavy-Duty Screw Anchor

    Standard Shipping

    $40.62

    Features

    • Tested in accordance with ACI 355.2, AC193 and AC106
    • Qualified for static, wind and seismic loading conditions
    • Thread design undercuts to efficiently transfer the load to the base material
    • Standard fractional sizes
    • Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
    • No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
    • Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
    • Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
    • Reuse of the anchor will not achieve listed loads and is not recommended
    Add To CartLoading Done
  • [50 Pack] Simpson Strong-Tie THDB25312CS Titen HD 1/4 in. x 3-1/2 in. Zinc-Plated Countersunk Head Heavy-Duty Screw Anchor

    Standard Shipping

    $53.42

    Features

    • Tested in accordance with ACI 355.2, AC193 and AC106
    • Qualified for static, wind and seismic loading conditions
    • Standard fractional sizes, hole size same as anchor size
    • No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
    • Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
    • 6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
    • Countersunk head allows screw anchor applications incompatible with a hex head
    • Available in 1/4″ and 3/8″ diameters
    Add To CartLoading Done
  • [50 Pack] Simpson Strong-Tie THD37212H Titen HD 3/8 in. x 2-1/2 in. Heavy-Duty Screw Anchor

    Standard Shipping

    $45.77

    Features

    • Tested in accordance with ACI 355.2, AC193 and AC106
    • Qualified for static, wind and seismic loading conditions
    • Thread design undercuts to efficiently transfer the load to the base material
    • Standard fractional sizes
    • Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
    • No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
    • Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
    • Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
    • Reuse of the anchor will not achieve listed loads and is not recommended
    Add To CartLoading Done
  • [50 Pack] Simpson Strong-Tie THD37600HMG Titen HD 3/8 in. x 6 in. Mechanically Galvanized Heavy-Duty Screw Anchor

    $188.46

    Features

    • Tested in accordance with ACI 355.2, AC193 and AC106
    • Qualified for static, wind and seismic loading conditions
    • Thread design undercuts to efficiently transfer the load to the base material
    • Standard fractional sizes
    • Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
    • No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
    • Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
    • Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
    • Reuse of the anchor will not achieve listed loads and is not recommended
    Add To CartLoading Done
  • THD37212RHP1

    [50 Pack] Simpson Strong-Tie THD50234RH Titen HD 3/8 in. x 2-3/4 in. Threaded Rod Hanger for 1/2-in. Rod

    Standard Shipping

    $93.08

    Features

    • Thread design undercuts to efficiently transfer the load to the base material
    • Serrated cutting teeth and thread design enable quick and easy installation
    • Specialized heat-treating process creates tip hardness to facilitate cutting while the anchor body remains ductile
    • Designed to install using a rotary hammer or hammer drill with standard ANSI drill bits — no special tools required
    • Installs with standard-sized sockets
    • Code listed for cracked and uncracked concrete applications under the 2015, 2012 and 2009 IBC/IRC, per ICC-ES ESR-2713
    • FM listed
    Add To CartLoading Done
  • THD37300CS6SS

    [50 Pack] Simpson Strong-Tie THD37400H6SS Titen HD 3/8 in. x 4 in. Type 316 Stainless Steel Heavy-Duty Screw Anchor

    Free Shipping

    $316.92

    Features

    • THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
    • Ideal for exterior or corrosive environments
    • Less carbon steel, less expansion
    • Installs with an impact wrench or by hand tool
    • Tested in accordance with ACI355.2, AC193 and AC106
    Add To CartLoading Done
  • THD37300CS6SS

    [50 Pack] Simpson Strong-Tie THD37500H Titen HD 3/8 in. x 5 in. Type 316 Stainless Steel Heavy-Duty Screw Anchor

    Free Shipping

    $346.15

    Features

    • THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
    • Ideal for exterior or corrosive environments
    • Less carbon steel, less expansion
    • Installs with an impact wrench or by hand tool
    • Tested in accordance with ACI355.2, AC193 and AC106
    Add To CartLoading Done
  • [50 Pack] Simpson Strong-Tie THDC25300H6SS Titen HD 1/4 in. x 3 in. Type 316 Stainless-Steel Heavy-Duty Screw Anchor

    Standard Shipping

    $190.14

    Features

    • THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
    • Ideal for exterior or corrosive environments
    • Less carbon steel, less expansion
    • Installs with an impact wrench or by hand tool
    • Tested in accordance with ACI355.2, AC193 and AC106
    Add To CartLoading Done
  • THD37300CS6SS

    [50 Pack] Simpson Strong-Tie THD37600H4SS Titen HD 3/8 in. x 6 in. Type 304 Stainless Steel Heavy-Duty Screw Anchor

    Free Shipping

    $288.46

    Features

    • THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
    • Ideal for exterior or corrosive environments
    • Less carbon steel, less expansion
    • Installs with an impact wrench or by hand tool
    • Tested in accordance with ACI355.2, AC193 and AC106
    Add To CartLoading Done
  • [50 Pack] Simpson Strong-Tie THD37500HMG Titen HD 3/8 in. x 5 in. Mechanically Galvanized Heavy-Duty Screw Anchor

    Standard Shipping

    $166.15

    Features

    • Tested in accordance with ACI 355.2, AC193 and AC106
    • Qualified for static, wind and seismic loading conditions
    • Thread design undercuts to efficiently transfer the load to the base material
    • Standard fractional sizes
    • Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
    • No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
    • Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
    • Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
    • Reuse of the anchor will not achieve listed loads and is not recommended
    Add To CartLoading Done
  • THD37300CS6SS

    [50 Pack] Simpson Strong-Tie THD37300H4SS Titen HD 3/8 in. x 3 in. Type 304 Stainless-Steel Heavy-Duty Screw Anchor

    Free Shipping

    $223.08

    Features

    • THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
    • Ideal for exterior or corrosive environments
    • Less carbon steel, less expansion
    • Installs with an impact wrench or by hand tool
    • Tested in accordance with ACI355.2, AC193 and AC106
    Add To CartLoading Done
  • [50 Pack] Simpson Strong-Tie THD37300H Titen HD 3/8 in. x 3 in. Heavy-Duty Screw Anchor

    Standard Shipping

    $59.69

    Features

    • Tested in accordance with ACI 355.2, AC193 and AC106
    • Qualified for static, wind and seismic loading conditions
    • Thread design undercuts to efficiently transfer the load to the base material
    • Standard fractional sizes
    • Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
    • No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
    • Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
    • Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
    • Reuse of the anchor will not achieve listed loads and is not recommended
    Add To CartLoading Done
  • THD37300CS6SS

    [50 Pack] Simpson Strong-Tie THDC25238H6SS Titen HD 1/4 in. x 2-3/8 in. Type 316 Stainless-Steel Heavy-Duty Screw Anchor

    Standard Shipping

    $183.25

    Features

    • THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
    • Ideal for exterior or corrosive environments
    • Less carbon steel, less expansion
    • Installs with an impact wrench or by hand tool
    • Tested in accordance with ACI355.2, AC193 and AC106
    Add To CartLoading Done
  • [50 Pack] Simpson Strong-Tie THD37300CS Titen HD 3/8 in. x 3 in. Zinc-Plated Countersunk Head Heavy-Duty Screw Anchor

    Standard Shipping

    $72.26

    Features

    • Tested in accordance with ACI 355.2, AC193 and AC106
    • Qualified for static, wind and seismic loading conditions
    • Standard fractional sizes, hole size same as anchor size
    • No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
    • Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
    • 6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
    • Countersunk head allows screw anchor applications incompatible with a hex head
    • Available in 1/4″ and 3/8″ diameters
    Add To CartLoading Done
  • [50 Pack] Simpson Strong-Tie THD37400H Titen HD 3/8 in. x 4 in. Heavy-Duty Screw Anchor

    Standard Shipping

    $62.38

    Features

    • Tested in accordance with ACI 355.2, AC193 and AC106
    • Qualified for static, wind and seismic loading conditions
    • Thread design undercuts to efficiently transfer the load to the base material
    • Standard fractional sizes
    • Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
    • No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
    • Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
    • Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
    • Reuse of the anchor will not achieve listed loads and is not recommended
    Add To CartLoading Done
  • THD37212RHP1

    [50 Pack] Simpson Strong-Tie THDB37158RH Titen HD 1/4 in. x 1-5/8 in. Threaded Rod Hanger for 3/8-in. Rod

    Standard Shipping

    $64.92

    Features

    • Thread design undercuts to efficiently transfer the load to the base material
    • Serrated cutting teeth and thread design enable quick and easy installation
    • Specialized heat-treating process creates tip hardness to facilitate cutting while the anchor body remains ductile
    • Designed to install using a rotary hammer or hammer drill with standard ANSI drill bits — no special tools required
    • Installs with standard-sized sockets
    • Code listed for cracked and uncracked concrete applications under the 2015, 2012 and 2009 IBC/IRC, per ICC-ES ESR-2713
    • FM listed
    Add To CartLoading Done
  • [50 Pack] Simpson Strong-Tie THDB25312H Titen HD 1/4 in. x 3-1/2 in. Heavy-Duty Screw Anchor

    Standard Shipping

    $42.54

    Features

    • Tested in accordance with ACI 355.2, AC193 and AC106
    • Qualified for static, wind and seismic loading conditions
    • Thread design undercuts to efficiently transfer the load to the base material
    • Standard fractional sizes
    • Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
    • No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
    • Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
    • Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
    • Reuse of the anchor will not achieve listed loads and is not recommended
    Add To CartLoading Done
  • THD37300CS6SS

    [50 Pack] Simpson Strong-Tie THD37300H6SS Titen HD 3/8 in. x 3 in. Type 316 Stainless-Steel Heavy-Duty Screw Anchor

    Free Shipping

    $288.46

    Features

    • THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
    • Ideal for exterior or corrosive environments
    • Less carbon steel, less expansion
    • Installs with an impact wrench or by hand tool
    • Tested in accordance with ACI355.2, AC193 and AC106
    Add To CartLoading Done
  • [50 Pack] Simpson Strong-Tie THDB25400H Titen HD 1/4 in. x 4 in. Heavy-Duty Screw Anchor

    Standard Shipping

    $45.08

    Features

    • Tested in accordance with ACI 355.2, AC193 and AC106
    • Qualified for static, wind and seismic loading conditions
    • Thread design undercuts to efficiently transfer the load to the base material
    • Standard fractional sizes
    • Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
    • No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
    • Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
    • Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
    • Reuse of the anchor will not achieve listed loads and is not recommended
    Add To CartLoading Done
  • [50 Pack] Simpson Strong-Tie THD37300HMG Titen HD 3/8 in. x 3 in. Mechanically Galvanized Heavy-Duty Screw Anchor

    Standard Shipping

    $72.85

    Features

    • Tested in accordance with ACI 355.2, AC193 and AC106
    • Qualified for static, wind and seismic loading conditions
    • Thread design undercuts to efficiently transfer the load to the base material
    • Standard fractional sizes
    • Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
    • No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
    • Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
    • Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
    • Reuse of the anchor will not achieve listed loads and is not recommended
    Add To CartLoading Done
  • [50 Pack] Simpson Strong-Tie THD37400HMG Titen HD 3/8 in. x 4 in. Mechanically Galvanized Heavy-Duty Screw Anchor

    Standard Shipping

    $90.00

    Features

    • Tested in accordance with ACI 355.2, AC193 and AC106
    • Qualified for static, wind and seismic loading conditions
    • Thread design undercuts to efficiently transfer the load to the base material
    • Standard fractional sizes
    • Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
    • No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
    • Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
    • Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
    • Reuse of the anchor will not achieve listed loads and is not recommended
    Add To CartLoading Done
  • [50 Rolls] TW898 S Max 21ga Stainless Steel Tie Wire for MAX RB398 series

    Special Order Shipping

    $879.40

    TW898 S Max 21ga Stainless Steel Tie Wire for MAX RB398 series

    Add To CartLoading Done
  • TW898-USA Buy America Rebar Tie Wire made in the USATW898-USA-TIE-WIRE

    [50 Rolls] MAX TW898-USA 21 Gauge Rebar Tie Wire made from Buy America Steel

    Free Shipping

    $357.11

    Features

    • Wire steel is melted, annealed and drawn in the U.S.A
    • Steel mill certification available
    • For use with MAX RB397, RB398, RB517 and RB518
    Add To CartLoading Done
  • TW898-EG max usa electro galvanized rebar tie wire

    [50 Rolls] MAX TW898-EG Electro Galvanized 21 Gauge Rebar Tie Wire

    Special Order Shipping

    $349.61

    Features

    • 21 Gauge Electro Galvanized Steel Tie Wire
    • Excellent resistance to corrosion and rust
    • For use with MAX RB397, RB398, RB517 and RB518
    Request QuoteLoading Done